FIR - Full 2020 Catalogue

FIR - Full 2020 Catalogue

Contents

FIR Tools

TOOLS

1-38

TITANIUM NUTS, BOLTS

39-72

NUTS, BOLTS, WASHERS

73-106

WORKSHOP

107-114

ELECTRICALS

115-140

RACE KIT / ACCESSORIES

141-144

MX - SERVICE & CONTROL

147-224

MX - ENGINE

225-246

MX - BRAKE & DRIVE

247-288

ATV - SERVICE & CONTROL

289-306

ATV - ENGINE ATV - BRAKE & DRIVE

307-320

321-344

ROAD - SERVICE & CONTROL

345-384

ROAD - ENGINE

385-396

ROAD - BRAKE & DRIVE

397-431

INDEX

432-433

FIND US ON FACEBOOK @FIRUK NEW ITEMS ADDEDWEEKLY

*Please visit our website for current prices

Chain Tools

FIR Tools

* Please note on Hi-Strength modern chains, it is advisable to grind the head of the rivet off first on one side on the chain *

FIR CHAIN BREAKER TOOL Chain cutting / breaker / link extractor tool. • Classic Motorcycle chain breaker • Suitable for chains sizes up to 5/8 x 3/8 or O and X-ring chains (pitch 415 - 530) • Enables chains to be accurately cut down / adjusted • Works with most classic motorcycles from the 1950s to 2020 • High quality steel construction - Strong durable design • Soft grip on handle • 6” in length approximately Part No. 00-730.DR Trade Pack of 10. 00-730.PK/10 Tip - Screw In Type Part No. 00-732.BK

00-741

00-741 Working

FIR CHAIN BREAKER TOOL Heavy duty chain cutting tool with folding handle. • Fits 420 to 530 chains (O-ring and Non O-ring) • Will push link pin completely through link / side plate • Handle folds away for easy storage • Durable drive pin is heat treated for strength and wear resistance

• Max pin extension to drive out chain links is 18mm. The maximum pin extension required to drive out the chain link is determined by measuring your chains width from outside face plate to outside face plate • Important Tip: On top end heavy duty chains it is best to grind the head off the rivet before splitting chain. Before use put some copper grease on thread Part No. 00-741.FIR FIR HEAVY DUTY CHAIN BREAKER TOOL Heavy duty chain cutting tool, 428-630. Workshop quality! • Pushes the pin all the way out • Works on 428-630 chains • Spare pin in handle • BZP plated finish • Important Tip: On top end heavy duty chains it is best to grind the head off the rivet before splitting chain. Before use put some copper grease on thread Part No. 00-740.FIR Trade Pack of 6. 00-740.PK/6

00-740

00-730

FIR HEAVY DUTY CHAIN CUTTING TOOL Chain cutting tool - Parallel pin type. • Pushes the pin all the way out, works on 428 - 630 chains

09-1002

09-1002 Working

• Important Tip: With todays very strong chains it is best to grind the head off the chain rivet before splitting. Some chains are so strong that this is a must do before trying to push the pin out! Part No. 09-1002.DR

FIR MINI CHAIN PRESS TOOL Mini chain press tool. • Tool box size budget price tool, for pressing on ‘press fit’ side plates • This tool is very easy to use and will fit all 520-530 chains • Hexagon key wrench is included with tool • Perfect addition for tool pack • Note: Does not rivet together rivet type links Part No. 00-070.F Trade Pack of 10. 00-070.F/PK10

00-070 Sample Image Working

00-070

FIR CAM CHAIN BREAK & RIVET TOOL Timing cam chain breaker & rivet tool - An ideal tool for breaking and riveting cam chains! • For timing, chain breaking and riveting • Ratchet handle included • One side is breaker, other side is rivet • Suitable for mini-bikes, scooters and motorbike engines • Weight: 0.7lbs • Works on No. 25 series timing chains • For use on timing chains Max. Height 4.7mm Part No. 00-424.F FIR CHAIN PRESS BREAKER TOOL Chain press / breaker (520-530 Chains) • For pressing on and off 520 and some 525 master link side plates • Light weight 6oz. including press plates and handle • Custom pouch holds tool securely • Body forged from high strength 4130 chrome-moly • Body bolt and extractor bolt manufactured from billet high strength 7075 T-6 aluminium Part No. 00-416.DR

00-424 Working

00-424

1

00-416

*Please visit our website for current prices

1. Tools pg.1-38.indd 1

29/11/2019 14:04:03

Tyre Levers / Bead Buddys

FIR Tools

FIR 16” HEAVY DUTY CNC TYRE LEVER CNC alloy handle tyre lever, 16” long (Sold Each). • Professional heaby duty tyre lever • Designed for use on the toughest tyre and rim combinations • Shaft made of forged chrome steel • Comfortable hand shaped aluminium handle, CNC machined from billet Alloy • Alloy handle has large knob on end that allows use with mallet for driving lever between bead and rim • Overall length 16” • Perfect tyre lever for fast mousse changing Part No. 00-502.EACH FIR 17” HEAVY DUTY TYRE LEVER CNC alloy handle tyre lever, 17” long (Sold Each) • Professional heavy duty tyre lever • Designed for use on the toughest tyre and rim combinations • Shaft made of forged chrome steel SCM440 • Comfortable hand shaped aluminum handle, CNC machined from billet Alloy • Alloy handle has large knob on end that allows use with mallet for driving lever between bead and rim • Overall length 17” • Handle Length: 4.1” • Spooned End O.D: 34 / 38mm • Perfect tyre lever for fast mousse changing Part No. 00-578 FIR TYRE LEVERS Tyre Lever 260mm, 10” loop handle - Long spoon loop with blue PVC handle. • Hardened alloy steel. Double compound curve makes removing the toughest tyre easy • Hard nickel silver finish • Each lever is 10 inches long 260mm (7.1oz) • Blue anti slip vinyl PVC cover • Width at spoon is 25mm • Curved end fits securely in the hand

00-502

00-578

• Also makes a great pry bar for removing bearings, etc. • Perfect size and shape for your bum bag or tool box • Recommended by top tyre changers 260mm Spoon Loop 00-956.ORO Trade Pack of 10. 00-956.PK/10

00-952

00-957

Tyre Lever with handle, 280mm. • Moulded high impact plastic handle for a positive grip, and easy comfortable use • Dropped forged hardened alloy chrome steel • Double compound curve makes removing the toughest tyre easy • Essential piece of kit for the workshop / van / bum bag and better than bending spoons! • Suitable for removal and fitting of off road tyres • Also makes a great pry bar for removing bearings, etc. 280mm Lever with Handle 00-957.EACH Trade Pack of 10. 00-957.PK/10

Tyre Lever - Forged steel, 400mm • Hardened chrome alloy steel

• Corrosion-resistant chrome-plated hardened tempered steel • Double compound curve makes removing the toughest tyre easy • Straight pattern tyre lever • Hook and taper ends • Tyre & Wheel Tools & Equipment • Also makes a great pry Straight pattern tyre lever 400mm Forged Steel Lever 00-952.FIR Trade Pack of 10. 00-952.FIR/PK10 400mm Heavy Duty Forged Steel Lever 00-952.HD Trade Pack of 10. 00-952.HD/PK10

00-956

00-956 Working

FIR ‘BEAD BUDDY’ OFF ROAD TYRE TOOL • Good auxiliary tool for tyre levers when replacing motorcycle tyres • A must for installing tubes • Provides an easy way to push the tyre bead down into the drop centre of the rim while using tyre levers • Slip the slot of the tool over the spoke and push the bead down on the opposite side of the tyre levers • It will facilitate pulling the tyre over the edge of the rim allowing the tyre installation • Best used in pairs • Steal plate with Tig welding - silver BPZ finish for long life Part No. 00-113.ORO.EACH Trade Pack of 10. 00-113.PK/10

00-113

00-113 Working

2

*Please visit our website for current prices

1. Tools pg.1-38.indd 2

29/11/2019 14:04:08

FIR Tools

Spoke Keys

FIR SPOKE KEY 6-IN-1 Spoke nipple key / wrench / spanner (6 in 1 Tool). • A quality heavy duty forged, carbon steel spoke spanner suitable for workshop use or in a bum bag • 3 sizes on each end: 5.6, 5.7, 6, 6.3, 6.6 and 6.8mm • Wide deep jaws avoided damage to nipples • Gold Zinc plated finish Part No. 00-630.FORGED Trade Pack of 10. 00-630.PK/10 FIR SPOKE KEY 6-IN-1 Spoke key, 6 in 1 Tool - Suitable for workshop use or in a bum bag! • Fits all standard spokes • Heavy duty carbon steel construction • 6 Spoke Nipple Sizes metric 4.2, 4.8, 5.3, 5.6, 6.0 and 6.3mm • 6 Spoke Nipple Sizes imperial 250”, .240”, .225”, .215”, .200” and .170” • Jaws are numbered and stepped for ease of use • Black finish • 4” - 100mm Long Part No. 00-640.EACH Trade Pack of 10. 00-640.PK10 FIR SPOKE WRENCH WITH 9 HEADS Spoke wrench, with 9 interchangeable heads. Sizes; 5.0, 5.4, 5.6, 5.8, 6.0, 6.2, 6.4, 6.6 and 6.8mm. • Specially designed spoke wrench with eight interchangeable sized heads • Easy and fast to swap heads • Rubber O-ring to stop turning when in use • Lightweight aluminium body • Inner rubber grip • Spanner heads made from chrome vanadium tool steel for long life, with a BZP finish • Suitable for adjusting spoke tension and correcting buckled wheels • Overall length with heads fitted 122mm • Size range covers from mini bikes to full sized bikes Part No. 00-902

00-630

00-640

00-640 Working

00-902

00-902 Working

FIR SPOKE SPANNER Designed for the professional wheel builder. This tool is unlike any other spoke wrench available. Featuring unique square end openings which grip the spoke nipple on all four sides, instead of just two, assuring that the nipple corners are not rounded off during tightening. • Chrome vanadium steel with a hard nickel pewter finish • Square end openings which grip the spoke nipple on all four sides • Offset slotted ends make it easy and quick to use • Sizes are 6mm and 6.3mm which will fit most Japanese dirt bikes and many street models Part No. 00-799A.FI

00-799

00-799 Working

3

*Please visit our website for current prices

1. Tools pg.1-38.indd 3

29/11/2019 14:04:08

FIR Tools

Wheel Tools

FIR PLASTIC RIM PROTECTORS Set of 2 nylon plastic rim protectors • Protects your alloy or chrome rims from scratches and dings caused by tyre changing tools • Retrieval cords are included for easy use • Made with new and improved Nylon PP material that is tougher, stronger, and more flexible • Rope is nylon and 85cm long • Very easy and fast to use • These protectors allow you to use tyre levers with confidence & will last for years • Can be used with any type of tyre levers Part No. 00-461.EACH Trade Pack of 10. 00-461_PK10 FIR WHEEL BEARING RETAINER DRIVER This special tool is used to install and remove the bearing retainer position on Honda Models. Honda CRF 250/ 450R, CRF 450X and the newest Honda models. • 6 square pins in width 4.6mm • The driver O.D 47mm Part No. 00-0172.DR

00-461 Sample Image Working

00-461

FIR KTM IMPACT AXLE REMOVAL TOOL KTM Impact Axle Remover Tool - Used to remover front wheel axle on KTM’s (WP Forks). KTM 950/990 Adventure Size; 50mm Part No. 09-1052

09-1052

FIR T-6 HEXAGON AXLE TOOL • Designed for internal hex axle removal on many late model sport bike applications • Four metric hex sizes: 17, 19, 22 and 24mm. 3/8” square drive on both ends • 7075 T-6 aluminium construction • 3/8” square drives are rated for a maximum of 90 ft-lbs Part No. 00-337.FI

00-0172

FIR FRONT AXLE TOOL (5in1) This professional grade, motorcycle front wheel removal tool. For quick and easy front wheel removal. • 5 size: 14, 17, 19, 22 and 24mm hexagon • Material: SCM440 • Heat Treatment: HRC38-42 • Surface Processing: Chemical nickel plating • Use with 3/8in. SQ. DR. on both ends and hex wrench • This tool will allow you to remove the front wheel on any motorcycle that has a 14, 17, 19, 22 and 24 mm female hex on the wheel or an where else a large hex is needed

00-337 Working

• 17mm is for use with Triumph motorcycles • 19mm is for use with Yamaha motorcycles • 22mm is for use with Kawasaki motorcycles • 24mm is for use with Suzuki & Honda motorcycles Part No. 00-7764

00-337

FIR RETAINER REMOVE TOOL (47mm) • Precision design prevents damage to the retainer ring after peened stakes have been removed by drilling • For use on 47 millimeter lock rings • Replaces OEM tools 07HMA-KS70100, and 07YMA-KZ40100 to remove and replace the rear wheel bearing/seal retainer rings, part numbers 41231-KZ4-J20 and 41231-KS6-700 • Versatile design features a 22 millimeter hex and 3/8 inches square drive Fits; Honda CR125 / 250R 2000-07, CRF 450R 2005-06, CRF 250X 2005-06, CR500R

00-7764

Sample Image of 00-7764 Working

1987-88 Part No.

00-213

4

00-213

*Please visit our website for current prices

1. Tools pg.1-38.indd 4

29/11/2019 14:04:09

FIR Tools

Wheel Tools

FIR RETAINER REMOVE TOOL (44mm) 44mm CR seal / bearing retainer removing tool for the rear wheel. • Designed to remove and install the rear wheel seal / bearing retainer nuts • Fits 84-01 Honda CR125 CR250, 1984-2001 CR500 • Precision design prevents damage to the retainer nut • 6 Square Lug / Tooth, OD 43.5mm • Versatile design features a 22mm hex and 3/8 in. square drive • Carbon Steel [S45C] and heat treated for durability

• Finished in Gold BZP plated • OEM No. 41231-KZ4-000 Part No.

00-138

00-138

FIR WHEEL BEARING REMOVER Wheel bearing remover set. • 9 piece set designed to remove wheel bearings safely and easily from motorcycle and ATV wheels • 7 Assorted Seal Collets: Ø10, 12, 15, 17, 19, 20, 25mm • Dependable split collet design • Includes new metric sizes to allow use with recent MX and Euro motorcycles • With durable plastic case for storage • Easy removal of wheel bearings fast without damaging wheel bearing seat • Covers Bearing sizes 10mm to 25mm ID. bores • 2 Drift Shafts: 250, 400mm • Top Tip: Warm around bearing seat for best results, this stops the bearing seat from wearing and going loose Drive collet size 24.9mm, 19.9mm, 16.9mm, 14.9mm, 11.9mm and 9.9mm. Part No. 00-055.FI

00-055 Working

00-055

FIR Tools

Tyre Valve Tools

FIR VALVE PULLING TOOL Allows for easy installation of tube valves. Simply pulls the tubes valve through the rim. ‘Air Valve Puller’ was designed to save time and your fingers! When changing a tyre or repairing a flat, just put the end of the ‘Air Valve Puller’ through the hole in the rim, thread it into the valve stem, then just pull the valve stem through the hole! The ‘Air Valve Puller’ can also be used to remove or tighten your valve core as well. • Brass air valve stem connector • Aluminum handle approximately 2-3/4” wide • Steel Cable approximately 8” Length • Fits securely in the hand • Easily inserts valve stem through rim Part No. 00-934

00-934

FIR TYRE VALVE REPAIR TOOL 4-in-1 Valve repair tool. Features & Benefits; • Re thread the external part of the valve stem • Remove the valve core • Extract a damaged valve core • Re thread the inside of the valve stem Part No.

Sample Image of a Valve Pulling Tool Working

00-623.EACH 00-623.PK/10

Trade Pack of 10.

00-623

5

*Please visit our website for current prices

1. Tools pg.1-38.indd 5

29/11/2019 14:04:13

Tyre / Pressure Gauges

FIR Tools

FIR EMERGENCY TYRE INFLATOR KIT Air bottle blow up air kit with x2 CO2 bottles. • This is a super small inflator kit which can be used for either motorcycles or mountain bikes • Comes complete with a small cycle adaptor to fit both types of tube valves • The controllable valve can be turned off or on, so only part of the cartridge need be used • 1 cartridge puts approximately 12 psi in a front 21” motocross tyre • Very easy and fast to use, the perfect kit for your bum bag for emergency use • Kit Includes: 2 Air cartridges, 1 Controllable valve, and 1 Cycle adaptor Part No. 10-200 Trade Pack of 6. 10-200.PK/6 CO2 Cartridges. 16 gram cartridge bottles to fit the above kit. The thread on the bottle is M10 x 1.00mm, which

may be used with any other matching adaptor. Overall dimensions: Diameter 22mm x 88mm long Part No. (x1 Pack of 3)

10-201.03/PK1 10-201.03/PK5

Part No. (x5 Packs of 3)

10-200

10-201

FIR DIGITAL TYRE PRESSURE GAUGE (2-150psi) • Digital pressure gauge with hose

• Gauge is constructed from reinforced nylon • Pressure Range: 2-150psi (0.2 - 7.00 bar) • LCD display (21 x 10mm) for easy reading • Perfect for workshop or track use Part No.

00-441

FIR LOW PRESSURE GAUGE (0-1 Bar) • 50mm Round low pressure gauge • With 900 chuck which can rotate 360° • Reading gauge diameter is 2” with a rubber protector outer shell • Pressure range: (0-15 psi and 0-1 kg/cm2), (0 to 1 Bar) & (0 to 100 KPA) Part No. 00-898.FIR

00-898

00-441

FIR Tools

Brake Tools

FIR CALIPER PISTON REMOVAL PLIERS • Specially designed locking pliers • Locking pliers for troublesome caliper pistons, very similar mechanism to mole grips, hard firm grip on the piston allows for a lot of pressure to be used to remove the piston • Pliers are simply clamped into the inner diameter of the caliper piston allowing it to be pulled out of the caliper • Caliper piston pot ID 17mm to 50mm Part No. 09-1037

Sample Image of 09-1037 Working

09-1037

FIR HYDRAULIC BRAKE BLEEDER TOOL Makes bleeding brakes a one person job! The unique check valve allows fluid and air to escape while preventing air from re-entering the system. Once this unit is primed with brake fluid, simply attach the hose to the caliper bleed screw and place the other end into a bottle. Once all the air is bled from the brake line, close the bleeder screw on the caliper and remove hose. Instructions and hose included. Part No. 00-804.FI Trade Pack of 10. 00-804.FI/PK10

00-804

6

*Please visit our website for current prices

1. Tools pg.1-38.indd 6

29/11/2019 14:04:18

Radiator Caps

FIR Tools

FIR RADIATOR CAPS (JAPANESE MODELS) High pressure radiator caps designed for todays racing 4-stroke and 2-stroke engines. Allows running a higher water system pressure and higher boiling point. Fits OE radiators or aftermarket. • High temperature silicone seals • Universal fit for most Japanese model bikes • Approximately Size. O.D 45.20mm Radiator Cap 1.1K (16psi) 18-080.11.FIR Radiator Cap 1.3K (19psi) 18-080.13.FIR Radiator Cap 1.4K (20psi) 18-080.14.FIR Radiator Cap 1.6K (23psi) 18-080.16.FIR FIR RADIATOR CAPS (EUROPEAN MODELS) High pressure radiator caps designed for todays racing 4-stroke and 2-stroke engines. Allows running a higher water system pressure and higher boiling point. Fits OE radiators or aftermarket. • High temperature silicone seals • Universal fit for KTM, Husky, Husaberg, European Models • Approximately Size. O.D 48.00mm Radiator Cap 1.1K (16psi) 18-086.11.FIR Radiator Cap 1.3K (19psi) 18-086.13.FIR Radiator Cap 1.4K (20psi) 18-086.14.FIR Radiator Cap 1.6K (23psi) 18-086.16.FIR Radiator Cap 1.8K (26psi) 18-086.18.FIR

18-080.FIR / 18-086.FIR

FIR RADIATOR CAPS (JAPANESE MODELS) • RADIATOR CAP 1.8 BAR - 26 PSI [JAPANESE BIKES] • ALUMINIUM ANODIZED WITH HARD BLUE FINISH.

• OEM Replacement radiator cap with Temp indicator on top. Always know what Tempera- ture your riding at so your bike never over heats. All caps are available in either 1.8 bar or 2.0 bar. Radiator Cap 1.8 Bar (26psi) 18-087.18.FIR Radiator Cap 2.0 Bar (29psi) 18-087.20.FIR

FIR RADIATOR CAPS (JAPANESE MODELS) • RADIATOR CAP 1.8 BAR - 26 PSI [Japanese] • ALUMINIUM ANODIZED WITH HARD RED FINISH.

• OEM Replacement radiator cap with Temp indicator on top. Always know what Tempera- ture your riding at so your bike never over heats. All caps are available in either 1.8 bar or 2.0 bar. Radiator Cap 1.8 Bar (26psi) 18-088.18.FIR Radiator Cap 2.0 Bar (29psi) 18-088.20.FIR

18-087.20.FIR

18-088.20.FIR

FIR RADIATOR CAPS (EUROPEAN MODELS) • RADIATOR CAP 1.8 BAR - 26 PSI [KTM / EUR] • ALUMINIUM ANODIZED WITH HARD BLUE FINISH.

• OEM Replacement radiator cap with Temp indicator on top. Always know what Tempera- ture your riding at so your bike never over heats. All caps are available in either 1.8 bar or 2.0 bar. Radiator Cap 1.8 Bar (26psi) 18-089.18.FIR Radiator Cap 2.0 Bar (29psi) 18-089.20.FIR

FIR RADIATOR CAPS (EUROPEAN MODELS) • RADIATOR CAP 2.0 BAR - 29 PSI [EUROPEAN] • ALUMINIUM ANODIZED WITH HARD BLUE FINISH.

• OEM Replacement radiator cap with Temp indicator on top. Always know what Tempera- ture your riding at so your bike never over heats. All caps are available in either 1.8 bar or 2.0 bar. Radiator Cap 1.8 Bar (26psi) 18-090.18.FIR Radiator Cap 2.0 Bar (29psi) 18-090.20.FIR

18-089.18.FIR

18-090.18.FIR

7

*Please visit our website for current prices

1. Tools pg.1-38.indd 7

29/11/2019 14:04:20

Cable Maintenance / Accessories

FIR Tools

FIR CABLE LUBRICATOR • The hand screws allows you to make the perfect seal on outer casing and inner wire • Used to inject lubricant into cable housing • Clamps over housing and wire allowing an aerosol can to be connected • Once lube runs out the far end, the cable is lubricated • Ideal for use with WD40, GT85 or Cable Lube Sprays • Fast and easy to use, with no mess • Aluminium billet body with hard anodized finish • Full body Silicone Rubber seal for long life and the perfect seal on any cable Part No. 00-990.EA Trade Pack of 10. 00-990.PK/10 Trade Pack of 50. 00-990.PK/50 FIR TWIN SCREW CABLE LUBRICATOR • 2 locking screws allows you to make the perfect seal on outer casing and inner wire • Used to inject lubricant into cable housing • Clamps over housing and wire allowing an aerosol can to be connected • Once lube runs out the far end, the cable is lubricated • Ideal for use with WD40, GT85 or Cable Lube Sprays • Fast and easy to use, with no mess • Aluminium billet body with hard anodized finish • Full body Silicone Rubber seal for long life and the perfect seal on any cable Part No. 00-991.DR

00-990.EA

00-991.DR

FIR HYDRAULIC CABLE LUBRICATOR Hydraulic cable lubricator, ideal for use on both clutch and brake cables. Cable is sealed in end of lubricator with oil, the oil is then forced all the way down the cable by turning the screw. Even old semi seized cables can be bought back to life.

• Aluminium body and hard anodized • Easy to use • Quick and effective • Use light oil like 3-in-1 or Similar • Professional quality tool Part No.

00-600

00-600

FIR CABLE GUIDE • Mounts to front number plate

• Brake line / front brake cable guide secures brake line while riding • Great for use with aftermarket triple clamps that lack a guide mount • High-quality injection moulded plastic • Very easy and fast to fit Part No. 75-901

FIR CABLE / HOSE CLAMP (SET OF 2) • Brake Line Clamps are the best way to secure the routing of your brake lines • Size range 20-25mm • They are made from aircraft grade billet aluminium 6061-T6 • Available for 25mm / 1 inch tube / A-arms • Hard Bright anodized finish • They are available in 4 different colours: Blue, Black, Red and Silver Part No. 02-700

75-901

02-700

FIR WIRE INNER STEEL Available in 1.5, 2.0 or 2.5mm diameters. (7x7 flexibility). Sold in 10 meter rolls. Diameter Part No. 1.2mm 14-910 1.5mm 14-911 1.5mm 14-911.77 2.0mm 14-912 2.0mm 14-192.77 2.3mm 14-913 2.5mm 14-914.77 3.0mm 14-916

Cable Wire

8

*Please visit our website for current prices

1. Tools pg.1-38.indd 8

29/11/2019 14:04:21

Cable Making Material

FIR Tools

Item Description

Part No.

Adjuster Honda type screw in adaptor for CR throttle 12-053 / 12-056 Angle Adjuster / Adapter Enables sharp bend on cable. Can use with 14-953 for Kawasaki’s Adapter Fits Keihin carb top like on KX‘s to take an standard cable Must be used with 14-951 or 14-952

14-950

14-952

14-953

Adjuster For front and Rear brake cables. No soldering needed. Complete with ferul and adjuster nut

14-955

Carb Idle screw Mikuni Each including lock nut

14-956

Mid Cable Adjuster

14-957

5mm

Solderless Nipples Pack Of 10 Control cable dia. 8mm x 10mm Solderless Nipples Pack Of 10 Control cable dia. 6mm x 8mm Solderless Nipples Pack Of 10 Pear shape

14-970.PK10

14-969.PK/10

14-972.PK10

Solderless Nipples Pack Of 10 Throttle cable with grub screw

14-971.PK10

Nipple round 5mm throttle end. Pack of 10 Nipple barrel 5 x 7mm throttle end. Pack of 10

14-974.PK10

14-978.PK10

Nipple barrel 6 x 7mm end (For 1.5mm wire). Pack of 10 Nipple mini sleeve 4 x 5mm carb end. Pack of 10

14-9600.PK10

14-975.PK/10

Nipple trumpet clutch end. Pack of 10 Nipple barrel 8 x 8mm clutch end. Nipple barrel 6 x 8mm clutch end.

14-976.PACK/10

14-979.PACK/10

14-977.PACK/10

14-982.EA

Throttle ferule outer each

14-982.PK10

Pack of 10 ferule outers

14-987.EA

Clutch / Throttle ferule each

14-987.PK10

Pack of 10 ferules

Cable Stopper 6mm thread with 8mm shank

14-966.EA

14-966.PK10

Pack of 10 cable stoppers

FIR CABLE RUBBER BOOT Cable rubber boot; Throttle / Clutch / Brake OD. 13mm x 26.50mm, Each OD. 13mm x 26.50mm , Trade Pack of 10

14-931

14-931.PK/10

ID. 10mm x 4.5mm Rubber Boot Seal

14-932 14-933

14-933

14-932

14-931

9

*Please visit our website for current prices

1. Tools pg.1-38.indd 9

29/11/2019 14:04:22

Engine Splitting / Clutch Tools

FIR Tools

FIR CRANKCASE SPLITTER Will work on most 2 and 4 stroke engines with vertically split cases. Movable fingers allow a multitude of bolt patterns to be used. Included 6 and 8mm mounting bolts. Specifications; Bolt: M8 X 90mm W/ Pitch 1.25mm X 3PC, M6 X 65mm X Pitch 1.0mm X 1PC, M6 X 57mm X P1.0mm X 1PC, M6 X 49mm X P1.0mm X 1PC, M14 X 180mm X P1.5mmX 1PC Note: When using this tool we fully recommend using thread protectors to avoid damage to the threads. Part No. 00-463.DR Keeps flywheels, rotors and sprockets from rotating while removing or tightening and holds sprockets and rotors, with holes centre to centre, at a minimum distance of 13mm and a maximum distance of 230mm. • Universal Pulley holder suitable for flywheel and clutch pulleys on a large range of motorcycles • Adjustable stop screw keeps tool open at set distance • Features 5 and 9mm pins - Round pegs mixed size fits most applications 5-9mm • A must have tool for your tool box if working on engines • PVC Dipped handle gives added comfort Part No. 00-216.FI Trade Pack of 5. 00-216.PK05 FIR ROTOR & SPROCKET HOLDER Scooter moped variator alternator clutch holding locking tool (universal). FIR CLUTCH & FLYWHEEL HOLDING TOOL • Designed to hold clutch baskets, flywheels, gears, sprockets etc. • Jaws open to 5” wide • Made of medium carbon steel with hardened jaws • 8mm pins on one side for holding the flywheels (only fits flywheel with an 8mm holes) • This tool is mainly used as a clutch hub holding tool • A very useful workshop tool for holding any kind of mechanical work • Ideal for Street, Dirt, ATVs and UTVs • BZP plated finish • Made from medium carbon steel with hardened jaws Part No. 00-890.DR Trade Pack of 10. 00-890.DR.PK10 FIR CLUTCH BLEEDING TOOL • Hydraulic clutch bleeder kit for KTM / Husaberg / Husqvarna’s (M8 x 1.5, Magura Clutch) • The bleeder kit simplifies bleeding the hydraulic clutch system • Includes everything needed to do the job 1x 35ml syringe, 1x bleed line, 1x bleeder fittings • Makes the bleeding of your clutch easy Part No. 09-1047

00-463 Working

00-463

00-216

00-890

FIR CLUTCH HOLDING TOOL (HONDA) • A clutch holding tool is used for the disassembly and assembly of the clutch • This tool is used to hold the clutch enabling the retaining nut to be removed or tighten without damage to the parts

• Carbon steel, with a BZP finish Fits Honda; CBR 1000RR 2008-11 Part No.

00-9021.FIR

09-1047

FIR CLUTCH NUT & OIL FILTER TOOL (HONDA) Oil filter and clutch hub spanner. • 3/8 drive, used for the removal of oil filter and clutch hub nuts • Made of heat-treated steel with black finish

• Use with a 3/8 inch driver • Inside diameter is 24mm • Designed to fit oil filter & clutch hub nuts on many Honda models, CB, CL, CT, SL, and XL, (both single and twin-cylinder machines) Part No. 00-007.FI

10

00-9021

00-007

*Please visit our website for current prices

1. Tools pg.1-38.indd 10

29/11/2019 14:04:23

Clutch Tools

FIR Tools

FIR CLUTCH NUT DRIVER 3/4” (POLARIS / KAWASAKI) • 3/4” nut driver for rebuilding primary clutches of all Polaris models and Kawasaki Prairie • Round in shape • Essential tool for servicing or rebuilding a clutch • Compare to Polaris OEM #2870338 Fits: P85 and P90 clutches found on Polaris ATVs and snowmobiles 1972 - present (except 900 RZR XP 4x4 2011-12 and 900 RZR XP 4 4x4 2012) Kawasaki 300/400 Prairie and 4x4 1999 - 02 Part No. 00-8485

00-8485

FIR CLUTCH DRUM (KTM) Clutch drum with 16 tooth gear on back. Fits KTM; 50 SX 2003-08, 50 SX Junior 2003-08, 50 SX Mini 2008,

50 Mini Adventure 2003-07, 50 Senior Adventure 2003-07, 50 Junior Adventure 2003. Part No.

04-5900

FIR 3-SHOE CLUTCH ASSEMBLY (KTM) KTM 50 after market 3-Shoe Clutch Assembly. Fits KTM; 50 SX 2003-08, 50 SX Junior 2003-08, 50 SX Mini 2008,

04-5900

04-5901

50 Mini Adventure 2003-07, 50 Senior Adventure 2003-07, 50 Junior Adventure 2003. Part No.

04-5901

FIR 2-SHOE CLUTCH ASSEMBLY (KTM) • Replica Morini 50cc engine clutch assembly (after market).

• 13mm, 12 tooth fits KTM 50cc pit bikes with Franco Morini engines • Complete 2 pad clutch assembly with slotted friction material • Fits KTM: All 50cc bikes 1994-2001 with black painted Morini Franco engine • Will also fit European bikes with Morini France engines (see website for list of applications) Dimensions; Clutch width: 81mm Centre Bore: 13mm, 12 tooth Thickness: 15mm Piston pin diameter: 13mm Part No. 04-5902

04-5902

04-600

FIR CLUTCH SHOE (HONDA) Honda clutch shoe. Fits Honda: ATC250 ES/SX 1985-87, TRX 250 1985-87, TRX 300 1988-99 Part No. 04-600

FIR DRIVE CLUTCH REBUILD KIT (8 Pcs) Drive clutch rebuild kit. This kit is designed to help rebuild the roller system on the primary

04-6002

04-619

clutch, on various Cam-Am models (see website for full fitment listings). Note: You might need 4 or 6 for each rebuild depending on model. Part No. 04-6002

FIR CLUTCH ROLLER SET (YAMAHA) Set of 8 clutch rollers. Used on Yamaha ATV’s (see website for full fitment listings). Weight: 14g, Size: 30x15mm Part No. 04-619

FIR KTM FLYWHEEL HOLDER TOOL (KTM) KTM Special Flywheel Holder. Fits: 2002-2008 KTM 50cc. • Length:190mm, Bore in centre: 24mm • Fits onto the ignition starter rotor • Holds the rotor without causing any damage Part No. 09-1049

09-1049

11

*Please visit our website for current prices

1. Tools pg.1-38.indd 11

29/11/2019 14:04:24

Universal Pullers

FIR Tools

FIR UNIVERSAL ROTOR PULLER • A specially designed tool for standard AC flywheel rings

• Features 6 different sizes; External M27x1.0L, M24x1.0R Internal M18x1.5R, M16x1.5R, M14x1.5R and M10x.125R • Quality cross handle puller • This tool fits 99% of Motorcycles • High Carbon tempered Steel • Finished in black Tips on use: • Make sure the flywheel thread is clean of dirt and not damaged before screwing the puller • After tightening use a hammer on the centre and tap to jolt free (not always need). • If using old flywheel pullers make sure the threads are in good condition before use to avoid damage to flywheel. Part No. 00-088.EACH Trade pack of 5. 00-088.PK5 in. Use copper grease on the puller threads, for long life. • Make sure the puller is fully screwed into the flywheel.

00-088 Diagram

00-088

FIR PULLER WITH PLATE & CENTRE PUSH BOLT Puller kit for pulling magneto flywheel or starter gear on Kawasaki Jet Ski 300/440/550. Will also fit the Yamaha WR 250F 2001-02, WR 400F flywheel and also some older Kawasaki 3 bolt flywheels. Kit includes; three 6x25mm and three 8x40mm bolts, 8mm bolt hole centre is 27mm to dead centre, 6mm bolt hole centre is 49.15mm to dead centre. Part No. 00-047.DR

FIR FLYWHEEL & PRIMARY GEAR EXTRACTOR (KTM) • Flywheel Puller / Primary Gear Extractor • Designed to remove the rotor and primary gear on a KTM 50’s • Comes with 4mm, 5mm and 6mm hardware • Overall length of bar: 90mm • Heat treated carbon steel with BZP finish • Center bolt M10x50mm Fits: KTM 50 Jr. Adventure / 50 Sr. Adventure / 50 Mini Adventure / 50 SX Mini (See website for full fitment listings) Part No. 00-312

00-047

FIR FLYWHEEL PULLER (SUZUKI) • Used for removal of the flywheel or rotor if applicable • Premium quality high carbon steel • Heat treated for strength and durability • Durable hot black oxide finish Fits: Suzuki RM80 1989-01, RM85 2002-12 Part No. 00-313

00-312

00-313 Working

00-313

12

*Please visit our website for current prices

1. Tools pg.1-38.indd 12

29/11/2019 14:04:24

FIR Tools

SwingarmTools

FIR SWING ARM NUT DRIVER (HONDA) This tool is necessary for removing the swing-arm pivot bolt and the lock nut on your ATV to replace your swing-arm bearings and seals. As you can see in the pictures above, one end of the tool is used for removing/replacing the swing-arm pivot bolt, and the other end of the tool is used for removing/reinstalling the swing-arm pivot lock nut. Buying this dual tool eliminates the need for purchasing two separate tools • Size. 4 lug 3.8 x 10.3mm • ID. 30.40mm x OD. 38mm x Overall length 87mm • Hexagon drive end 17mm AF FIR SWING ARM NUT DRIVER SET Swing Arm Nut Driver Set of 6. Set with six different lock nut drivers for swing arm and steering nuts. Use on the following models: Aprilla RS 125, Suzuki SV 650/1000, DL 650/1000, V-Storm, Various Hayabusa’s, B-King & GSX-R 750, 1100/1000 Honda 80-12 CB/CBX/CBR/GL/VFR/VT, Gold Wing, Shadow & Magna Kawasaki ZX 6RR/6R 03-04, Z750 04-10, Z750S 05-06, Z1000 07 -08, ZZR 02-03. Kawasaki ZX12R 01-05, ZX6R/600 05-10, ZX6RR 05, ZX6R/636 05 -06, zx10R 04-10, Z1000 10, GTR 1400 08-10 & ZZR 1400 06-10 Part No. 00-8491.FIR

00-8491

• Has a special 4 lug design • Carbon steel construction • 38mm fits most Honda ATV’s

• OEM quality swing-arm pivot bolt lock nut removal install tool • Fits many Honda TRX models (see website for full fitment listings) Part No. 09-1041

09-1041

FIR Tools

Oil Tools

FIR OIL FILTER STRAP WRENCH • Fits all spin-on type oil filters • 2 Different designs for use with a 3/8 or 1/2 drive ratchet • Can also be used to hold other cylindrically-shaped parts Part No. 00-164.FI

FIR OIL LEVEL DIP STICK 78mm Long, 18mm Thread. CRF50 70 110 125cc Dirt Pit Bike YCF SDG SSR TTR Part No.

00-164 Working

00-164

08-5100.FIR

107mm Long, 18mm Thread. GY6 50cc 125cc 150cc Oil Dipstick 139QMB 152QMI 157QMJ Scooter Moped Part No. 08-5101.FIR

146mm Long, 19mm Thread. 125CC 150CC 200CC Dirt Pit Bike YCF SDG SSR TT Part No.

08-5102.FIR

FIR OIL MEASURING TUBES Oil measure / mixing tube • No more guessing the exact oil required • Use for mixing 2 stroke and 4 stroke gear and engine oil • Easy and accurately measures your oil fuel mix • Manufactured fuel and oil resistant plastic Oil Measuring Tube, 250ml 77-0030.EACH Trade Pack of 10. 77-0030.PK/10 Oil Measuring Tube, 500ml 77-0045.EACH Trade Pack of 10. 77-045.PK/10 Oil Measuring Tube, 1000ml 77-0047.F Trade Pack of 10. 77-0047.F_PK/10

08-5100

08-5102

77-0030

13

*Please visit our website for current prices

1. Tools pg.1-38.indd 13

29/11/2019 14:04:28

Compression Testers / Leak Down Tools

FIR Tools

FIR COMPRESSION TESTER WITH ADAPTERS • Compression tester, includes dial gauge (measures up to 300 psi) • An essential tool for determining gas leakage from cylinders

• Results shown from a clear, easy to read dial on a scale that ranges from 0-300psi • Pressure is retained in the device and released by pressing a button on the side of the gauge meaning the test can be conducted with one person • Note: 10-12mm & 14-18mm adaptors which fits most gasoline engines Part No. 00-3350.FIR

00-3350

FIR Tools

Plug Tools

FIR RATCHET PLUG WRENCH TOOL Spark Plug Wrench, liquid cooled 2-strokes Fits; M14 Thread

This tool is made specifically to fit between the gas tank and the cylinder head on many water cooled, 2-stroke motocross models where there is limited space to remove the plug. The new 13/16” ratchet spark plug wrench is made specifically for water cooled 2-stroke motorcycles, ATV’s and personal watercraft. The ratchet mechanism makes installation and removal of the spark plug very easy. The ratchet mechanism works one way, just flip the wrench over to install the plug. Part No. 00-823.FIR Trade Pack of 10. 00-823.PK/10

00-823

FIR PLUG SPANNER 4 Stroke plug spanner. This long plug spanner is ideal for use on any deep fitting plug on 4-stroke bike fitted with a 12mm plug. Overall starting length 160mm x 16mm hex socket. Part No. 00-7800.EACH Trade Pack of 10. 00-7800.PK10

00-7800

FIR RUBBER SPARK PLUG CAP WITH WIRE Rubber spark plug cap with HT lead 19” of wire Without resistor Part No. 37-001.EACH Trade Pack of 10. 37-001.PK10

37-001

14

*Please visit our website for current prices

1. Tools pg.1-38.indd 14

29/11/2019 14:04:33

Plug Tools

FIR Tools

FIR SPARK PLUG SPANNERS 10/12/14mm Doublend

00-821

12mm Deep 4-Stroke (Each)

00-822.EACH 00-822.PK/10 00-830.EACH 00-830.PK/10 00-831.EACH

12mm Deep 4-Stroke (Trade Pack of 10)

14mm Fixed Handle (Each)

14mm Fixed Handle (Trade Pack of 10) 17mm with 3 Spoke Sizes (Each)

00-830

17mm with 3 Spoke Sizes (Trade Pack of 10)

00-831.PK/10

00-831

FIR 14mm SPARK PLUG SOCKET • Thin wall design allows for use in small plug cavities • Can be driven with 1/4” drive ratchet, or 13/14mm wrench, socket or T-handle • Rubber plug retainer • Chrome steel in bright silver finish • Fits late model KTM 4-Stroke and Honda CRF250/450 Part No. 00-847.DR FIR 4-STROKE SPARK PLUG TOOL • Specially designed for water cooled 4-strokes with 16mm plugs • 2-step extension, swivel or fixed • Manufactured with chrome alloy steel with a chrome plated finish for years of service • Small and neat very compact for bum bag • Socket can be used with a screwdriver to hold the front 19mm hex axles of late model 4-strokes • For use on models like KTM 4-strokes, DRZ400, CRF450R, YZF/WRF400/426, YZF250, KLX300, DVX400 and more... Part No. 00-144.FIR FIR SCREW CAP PLUG HOLDER / PROTECTOR • Keep your spark plug safe, clean and dry when in your tool box or bum bag • Features a screw cap that makes it easy to get at your plug, even with tired fingers! • Great for trail packs, back packs, or tool boxes • Works with all 2-stroke and 4-stroke spark plugs • Tapered top and 3/8” wall design protects spark plug against hits and drops • Available in Blue or Yellow Part No. 77-0075 Trade Pack of 10. 77-0075_PK/10 FIR SPARK PLUG CAPS Rubber waterproof covers and positive attachment mechanisms on both ends for shake-proof grip. This cap does not have a resistor. Available in Black, Blue, Green, Orange or Red. • Accept up to 8mm plug wire

00-822

00-821

00-847

00-144

77-0075.YELLOW

77-0075.BLUE

• T: Special 90° elbow • Fits 14mm threads

• For terminal nut • Rubber sheathed • For recreational / anti-vibration Spark Plug Cap

77-0075.YELLOW Working

77-0075.BLUE Working

37-000

Trade Pack Of 20

37-000_PK/20

Rubber plug cap universal (Black) • 90° Heavy duty black rubber plug cap • Screws into HT lead • Waterproof • Clamp to tighten around the plug lead to make a good waterproof seal

• Small and neat fast and easy to fit • This cap does not have a resistor Rubber Plug Cap

44-150.E

37-000

Trade Pack Of 20

44-150.PK/20

Silicone rubber spark plug cap - Angled (Classic design) • Silicone soft rubber longer lasting and high temp heavy duty • Plug Cap 90° degree angle • Screws on to copper HT cable between 5mm and 8mm diameter • Clamp to tighten around the plug lead to make a good waterproof seal • Waterproof seal around plug due to soft silicone rubber

• Small and neat fast and easy to fit • This cap does not have a resistor • Top of spark plug needs the nipple on Silicone Plug Cap

44-152.E

Trade Pack Of 10

44-152.PK/10

44-150

44-152

15

*Please visit our website for current prices

1. Tools pg.1-38.indd 15

29/11/2019 14:04:35

Valve Tools

FIR Tools

FIR OFF-SET FEELER GAUGE SET • Combination Metric and SAE offset feeler gauge set. 0.008” to 0.026” (0.203 - 0.660mm) • 12 blades • Metric Imperial Offset Dual Marked Reading Measure

• Being offset makes them ideal for adjusting valve tappet clearances • In a neat fold away design, make it looks perfect and easy carry • Material: Stainless steel Part No. 00-443

00-443

FIR FEELER GAUGE SET Feeler Gauge. Metric set. Carbon steel 0.05 - 1.0mm. 13mm x 100mm (1/2” x 4”) blades.

• Checks flatness or gaps between mating parts • Feeler thickness gauge includes a steel case • Locknut holds one or more leaves in any position • Each blade has been hardened, tempered and polished • Clear etching of thickness for easy identification • Blades fold into the holder for safe keeping Part No. 00-881.FIR

FIR MULTI VALVE TOOL • Used to install valve spring keepers • Replaces the large cumbersome valve spring compressor

00-881

• The small tool is designed to fit valves of 4- and 5-valve-per-cylinder heads (5.5mm valve stem diameter or smaller). The larger tool is designed to fit the vales of 4-valve-per-cylinder heads (5.5mm valve stem diameter or larger under 40lbs. seat pressure) • Will dramatically reduce the time necessary to replace valves in modern 16- to 20-valve heads Multi Valve Tool (Small) 00-177 Multi Valve Tool (Large) 00-178

FIR VALVE GRINDING KIT Used for grinding valves in vehicle engines. Start refacing with coarse paste and change to fine paste to achieve a perfectly smooth finish. Valve Tool Set. 35/28 & 16/21 Set of two valve grinders with wooden shafts. Suitable for grinding-in most engine valves. Features four sizes of rubber suction cup. Will work on valve heads 16mm to 28mm. Grinding Paste. ABRO GP-201 Specially formulated for grinding automotive valves. Unique can design opens for easy access to either fine or coarse paste-like grit. 5oz/140g. Part No. 00-090

00-178

00-177

00-178 Working

00-090

00-090 Working

16

*Please visit our website for current prices

1. Tools pg.1-38.indd 16

29/11/2019 14:04:36

Piston Tools

FIR Tools

FIR PISTON PIN REMOVING TOOL (13-22mm) • Top quality tool for removing pressed in gudgeon pins • May be used with engine in frame, on single or multi cylinder engines • Fits all piston sizes from 40mm to 100mm and all piston pins from 12mm to 25mm - including all single cylinder engines from 50cc to 600cc and all sizes 2, 3 or 4 cylinder • Will not damage piston or con-rods during removal Part No. 00-068

00-068 Working

FIR PISTON PIN REMOVING TOOL (14-17mm) • Economy piston pin pulling tool • Interchangeable piston adapter dowels with ODs 14mm & 17mm • Center stud of M8, so the piston pin must have a center hole of 8mm or more • Body made of durable 6061 aluminum with blue anodized finish • Fits all motorcycle and ATV piston pins • Works on both full skirt and short skirt pistons 2 and 4 strokes • Durable blue anodized finish with knurled finish for the best grip • Overall length of body 130m • Sliding T-Handle top screw also with 14mm hexagon if need Part No. 00-526

00-068 Working

00-526 Working

FIR PISTON RING EXPANDER PLIERS • Professional tool for commercial or occasional use • Suitable for the removal of piston rings on most cars / vans / motorbikes / trucks etc. • Allows easy removal without breaking the piston ring • Used to remove and mount piston rings easily and quickly, without damage and bump of the piston rings • Smooth gripping edge to prevent damage to the piston ring • Suitable for piston rings from 50mm 100mm • Spring loaded tool • Soft rubber handles for comfort and grip when using this tool Part No. 00-0175

00-526

FIR PISTON BASE ALLOY HOLDER Alloy plate that slips under the piston to hold things steady when rebuilding the top end of the engine. The grove fits around the connecting rod and flat onto the crankcases, then the bottom of the piston drops down onto it to keep the piston 100% up right as you lower the cylinder onto the rings. This makes fitting the Piston into the cylinder much easier on 2 and 4 stoke engines. Part No. 00-004.TZ

00-0175.DR Working

00-0175

00-004

00-040 Working

17

*Please visit our website for current prices

1. Tools pg.1-38.indd 17

29/11/2019 14:04:36

Timing Tools

FIR Tools

FIR TIMING PLUG SLOT DRIVER • Timing Plug Slot Driver • Constructed from aluminium alloy • The blade of the timing toll plug is 7/8” (22mm) • Fitted on most ATV’s and Motorcycles. Part No.

00-0174

FIR DEGREE KEY (YAMAHA) The Team Alba offset timing degree key gives you an extra 4 degrees of advanced timing. You will gain between 2 and 2.5 H.P. at the wheels. • Installation is easy, but be sure to use the proper flywheel remover tool. Universal tools will break your flywheel • Fits all years Yamaha Banshee 350 • Instructions are included Part No. 82-8300

00-0174

82-8300

FIR WOODRUFF KEY Woodruff keys. Available in 2 sizes; 3 x 6.5 x 16mm OR 3 x 5.00 x 13mm Woodruff Key 3x6.5x16mm, Each Trade Pack of 10 44-468.EA 44-468.PK10 Woodruff Key 3x5.0x16mm, Each Trade Pack of 10 44-469.EA 44-469.PK10

44-469

FIR TIMING TOOL (DUCATI) • Professional timing / degree tool • Makes accurate adjustments to your bike • Turn marks on the degree wheel to perfectly time the ignition • Works on most High Performance Street Model Ducati’s 1990 & Newer • Fits: Ducati 1990 to current (750/900/916) • Note; Remove spark plugs and place engine in neutral while using this tool Part No. 00-7907.DR

00-7907.DR

00-7907.DR Working

FIR Tools

Gear Holding Tools

FIR PRIMARY GEAR HOLDER • Primary gear holder • It fits 46mm diameter gears with 23 teeth • This tool helps you to hold the primary gear while disassembling and assembling the

engine without damage to the parts • Works on KTM Motorcycles 1998-on Part No.

09-1051

09-1051

09-1051 Working

FIR CAM GEAR REMOVAL & INSTALLATION TOOL HOLDER An essential tool to help in the easy removal and installation of the cam gears and do a full engine rebuild on your Triumph twin motorcycle. This tool is absolutely essential to remove and replace the cam gears when the need to change cams and do a full engine rebuild on your Triumph twin motorcycle occurs. • Holder Length; 73mm, O.D: 35mm, I.D: 31mm • Thread; 1.25mm • Bolt Length; 9 x 90mm = 2 pieces Part No. 00-0094.FIR

Sample Image of 00-0094 Working

18

00-0094

*Please visit our website for current prices

1. Tools pg.1-38.indd 18

29/11/2019 14:04:40

Carburettor Tools

FIR Tools

FIR CARBURETTOR ADJUSTER DRIVER • Made from alloy steel S45C • Works with Mikuni or Keihin carburetors • 8mm hex nut and screwdriver slot adjusting bolt • 11 inches (280mm) long • Makes adjusting your hard to reach mixture screws easy Part No. 00-051.FIR

00-051.FIR

FIR JET NEEDLE REMOVAL TOOL (KEIHIN CARBS) • FCR Jet Needle Tool • Tool for easy removal of the jet needle on any Keihin FCR carb. • Makes simple and safe removal of needle jets • Overall Length 125mm Fits: YFZ450, YZ250F, KX250F, CRF250R, CRF450R, RMZ250, KX450F Part No. 09-1046

09-1046

FIR 90 ° PILOT SCREWDRIVER • Carburettor pilot screw tool • Designed for those hard-to-reach air/fuel mixture screws on most multi-cylinder motorcycles • Straight-slot blade tip can be rotated by rotating the handle • Length is 17 inches with a 110° angled head to extend reach 1 inch

• Tip height is adjustable, and can be set in place during use • Metal shaft with knurled grip area and hard plastic handle Part No. 00-137.DR

00-137

FIR CARBURETTOR TOOL SET Carburettor Tool Set - 4 pieces • Steel with zinc plated finish Set includes: • 6mm hex for main jet • 3mm allen for removing float bowl • Short slotted screwdriver x1 PC (for a few spare main jets) • Long-reach stright slot for pilot jets Part No. 00-1161

FIR CARBURETTOR JET WRENCH • Jet removal key 6mm (1/4”), Hexagon • Fits Mikuni and Keihin hexagon style main jets • Compact wrench allows you to take jets out, with carburettor still on the bike • Made from High impact Nylon • Two finger lugs no need for any other tools • Red Only Part No. 00-158

00-1161.FIR

00-1161 Working

FIR CARBURETTOR SYNCHRO (UNIVERSAL) • Precise four channel vacuum indicator designed specifically for intake synchronization of engines with multiple carburetors or throttle bodies (maximum vacuum rating for this tool is 40cm Hg) • Mercury-free design • For use with any 2, 3 or 4 cylinder four stroke motorcycles • Spill proof design allows tool to be stored in a horizontal or vertical position • Easy to read scale for precise synchronization • Unaffected by ambient pressure changes • Includes hang hook to clip onto the handlebars for easy use • Rugged, impact resistant ABS enclosure with convenient storage area for adapters • Rubber feet on enclosure bottom helps prevent sliding

• Includes hoses, 5mm adapters, in-line restrictors and instructions • 5mm adapters are used on many Honda and Suzuki models • Optional 6mm adapters are available for use on most Yamaha models • Most Kawasaki models do not need adapters • Patented design Part No. 00-8080.FIR

00-158

19

*Please visit our website for current prices

1. Tools pg.1-38.indd 19

29/11/2019 14:04:41