Data Loading...
Magic Heat Operator Manual
183 Downloads
32.86 MB
Twitter Facebook LinkedIn Copy link
RECOMMEND FLIP-BOOKS
Magic Heat French Operator Manual
1 9 HY-C COMPANY 10950 Linpage Place St. Louis, Missouri 63132 (800) 325-7076 | www.hy-c.com | sales
FC1000 Operator Manual | 8.2018
Store Phone #: City Date Purchased: State, Zip Installed By: Phone # Installation Date: Product Info
FC1900 Operator Manual | 3.2018
8 inches. • Completely avoid using if at all possible. If circumstances necessitate the use of wet o
LintEater Operator Manual
Rod connections. 3. Connect one rod at a time until you reach the opposite end. Note: If your vent i
SF1000E Operator Manual | 1.2021
unit exhibits symptoms of obvious over-firing, deliberate abuse or negligence, improper installation
SF1000 Operator Manual | 8.2018
Store Phone #: City Date Purchased: State, Zip Installed By: Phone # Installation Date: Product Info
SootEater Operator Manual
plastic. Poke hole in plastic, then feed rod through before sealing completely. Step 5- Rotary clean
Ignite Tech | HD90X Operator Manual
CGA-B149.2 (for gas-fired). THIS IS A WOOD AND COAL BURNING FURNACE ONLY AND SHOULD NOT BE ALTERED I
Q55 Coulter Operator Safety Manual
s into cylinders and operating tractor hydraulics to achieve full uninterrupted travel of cylinder s
LISTED HEAT RECLAIMER 915U
Models MH-6 thru MH-8
Models MH-6-R thru MH-8-R
The temperature of the flue gases shall be determined before installing the heat reclaimer. The
1. Any flue or stove piping below Magic Heat must be 24 gauge metal or heavier to provide adequate supprt. Horizontal run of pipe must pitch upward toward the chimney at least 1/4 inch per foot of run.
(Not necessary for gas).
well
Units with serial numbers lower than serial # U 334 601 require annual oil service. Remove the back as described under “In Case of Power Failure” section. Then remove fan blade and six (6) screws that secure heat shield to back. Clean dust away from oil ports (See Figure 6) and oil motor with two (2) drops of SAE 20 light motor oil, one in each oil port.
Spot
Operate soot scraper at least daily for wood and coal burning and at least once a week for oil burning as a safety precaution against flue stoppage. Check stack vent yearly before each heating season begins. This should be done by a qualified gas heat serviceman.
MAGIC HEAT PARTS LIST Outer Case Assembly** Inner Case Assembly** Outer Back Motor Fan Cord (Electric) Thermostat (Wood, Coal, and Oil) Thermostat - Natural Gas Name Plate Sheet Metal Screws Brushing (Cord) Instructions Toggle Switch Switch - Natural Gas Indicator Plates Indicator Plates - Natural Gas Ground Wire Thermostat Leads Heat Shield Junction Box Standard Outside Soot Scraper Knob
1) 2) 3) 4) 5) 6) 7) 7)
MHSO** MHSI** MH-3 MH-12 MH-13 MH-l4 MH-15 MH-40G MH-16 MH-17 MH-18 MH-25 MH-31 MH-31G MH-32 MH-32G MH-34 MH-38 MH-41 MH-42F MH-77F
* * 8 *
9) 9)
* * *
10) 11) 12) 15) 22)
Complete Standard Back Assembly (Includes: 3, 4, 6, 8, 9, 10, 11, 12, 13)
*Not pictured in illustration.
**NOTE: Please specify flue diameter and model number when ordering part numbers.
MH-76 11/19
HY-C COMPANY 10950 Linpage Place St. Louis, Missouri 63132 (800) 325-7076 | www.hy-c.com | [email protected]