Data Loading...

2945D 2965D Combined 3PL Rigid Speedtiller Operator Manual

241 Views
8 Downloads
3.77 MB

Twitter Facebook LinkedIn Copy link

DOWNLOAD PDF

REPORT DMCA

RECOMMEND FLIP-BOOKS

2945D 2965D Combined 3PL Rigid Speedtiller Operator Manual

2945D-2965D 3PL RIGID SPEEDTILLER

OPERATOR & SAFETY MANUAL

MODELS: 2945D,2950D,2955D,2960D & 2965D

74 Young Rd | PO Box 340, Cowra, NSW 2794 | AUS

2945D - 2965D 3PL SPEEDTILLER

OPERATOR & SAFETY MANUAL

Wou ld you l i ke a copy of th i s manual emai l ed to you?

Send your reques t to mar ket i ng@k- l i ne . net .au or scan here :

2945D - 2965D 3PL SPEEDTILLER

OPERATOR & SAFETY MANUAL

Dear Customer

Thank you for purchasing a Three Point Linkage Speedtiller made by K-Line Industries. We would like to assure you that you have made a good choice, and will be able to rely on this high quality piece of equipment. We ask you to follow the user’s instructions closely, as this will ensure that you experience the benefits of using the machine without experiencing the unnecessary down time caused by misuse. When you receive the machine, make sure that it has not been damaged during transportation and that no parts are missing. Contact your dealer immediately if any parts are missing. Ensure that all components are correctly adjusted. The return of the Warranty Registration Form Page 51 will enable a prompt and efficient identification of your Speedtiller and attention to any concern you may have. Before operating PLEASE TAKE THE TIME TO LEARN the process of operation. Do not take the unit for granted; ease into becoming familiar with your new equipment. The operator should be a responsible adult familiar with farm machinery and trained for this purpose. Do NOT allow persons to operate or assemble the unit until they have read this manual and understand how to use this machine, and observe the safety precautions. Never exceed the limits of this machine. If its ability to do a job, or to do so safely, is in question - DO NOT TRY IT.

DO NOT attempt to operate this equipment under the influence of drugs or alcohol.

Remember - Your best assurance against accidents is a careful and responsible operator.

If you have any questions not answered in this manual or require additional copies or the manual is damaged, please contact your dealer or be free to phone us on our free call number:

AUS - 1800 194 131

The team here at K-Line Agriculture trust you enjoy a good season and prove the benefits of owning and operating a quality machine that is built to perform.

Signed:

David Larsen National Operations & Development Manager, K-Line

2945D - 2965D 3PL SPEEDTILLER

OPERATOR & SAFETY MANUAL

OP & SAFETY MANUAL Table Of Contents CUSTOMER LETTER 3 LEGAL DISCLAIMER 5 SPECIFICATIONS 5

Front Disc Standard Factory Setting

27 28 28 28 29 30 31 32 32 32

Adjustment Procedure Side Coulter Adjustment Excessive Trash Conditions

Useful Hints

INTRODUCTION

Performing Maintenance

Availability Of Genuine Parts

6 6

Maintenance & Safe Procedures

Identifying The Machine Tractor Requirements

After Delivery Check List

6 6

Wheel Bearings

Definitions Used In This Manual

Lubrication Of Heavy Duty Rear Roller Bearings

RISK MANAGEMENT

7-9

EXPLODED VIEWS

33-40

Identifying Hazards

7 7 7 7 8

Risk Assessment

Speedtiller Jump Arm Assembly

33 34 35 36 37 38 39 40

Risk Control

Disc Arm Bearing

Monitor & Review Control Measures

Side Coulter

Risk Assessment Score Chart

Adjustable Extension Deflector 60mm Roller Bearing Shaft

Risk Assessment Table

SAFETY

10-22

Peer Roller Bearing

Important Notice (MUST READ)

10 11 11 12

Bolt - On Roller Pin/Hub Heavy Duty Roller Bearing

Safety Alert Symbol

Signal Words

Safety Decals & Placement

Rear Roller Bearing Fitting Instructions

Safety Decals

13-16

Logo Srickers & Placement

17 18 19

Bolt Torque Tables

42-43

Safety Sign Care

Priming Hydraulic System Hydraulic System Failure Hooking/Unhooking To Tractor

TESTIMONIAL PERMISSION FORM 45-46

20 21 22

WARRANTY Warranty Letter

49-53

Transport/Roading

48 51 53

Warranty Registration Form Warranty Request Form

FIELD OPERATION Speedtiller Start-Ups

23-32

23 24 25

Speed Range

Tracking Adjustments

Front Disc Gang Lateral Positioning

26-28

END OF DOCUMENT

2945D - 2965D 3PL SPEEDTILLER

OPERATOR & SAFETY MANUAL

LEGAL DISCLAIMER LAST UPDATED: 27/07/21

The information contained in the K-Line Industries Pty Ltd (also trading as “K-Line Ag” and “K-Line Agriculture”) manual is for general information purposes only. K-Line Industries Pty Ltd assumes no responsibility for errors or omissions in the contents of the book. In no event shall K-Line Industries Pty Ltd be liable for any special, direct, indirect, consequential, or incidental damages or any damages whatsoever, whether in an action of contract, negligence with the use of the Service or the contents of the Service. K-Line Industries Pty Ltd reserves the right to make additions, deletions, or modification to the contents of this manual at any time without prior notice.

SPECIFICATIONS

RIGID MODEL SIZES

2945D

2950D

2955D

2960D

2965D

OPERATING WIDTH APPROX.

4.5M (14.8 FT)

5.0M (16.4FT)

5.5M (18.0FT)

6.0M (19.7FT)

6.5M (21..3FT)

156-200KW 210-270HP

186-209KW 250-280HP

260-290KW 190-220HP

224+ KW 300+ HP

254+ KW 340+HP

TRACTOR POWER RANGE

NUMBER OF DISCS

SPEEDTILLER WEIGHT DEPENDING ON ROLLER ETC.

3472KGS (7656LBS)

4350KG (9592LBS)

4188KGS (9235LBS)

4900KGS (10805LBS)

5004KGS (11034LBS)

TOWING TRANSPORT HEIGHT

TRANSPORT HEIGHT

1.35M (4.4FT)

1.4M (4.6FT)

TRANSPORT WIDTH

4.8M (15.7FT)

5.4M (17.7FT)

5.8M (18.9FT)

6.3M 20.7FT)

6.8FT (22.3M)

TRANSPORT LENGTH

2.4M (7.9FT)

6.3M (20.7FT)

2.4M (7.9FT)

Figure 1

2945D - 2965D 3PL SPEEDTILLER

OPERATOR & SAFETY MANUAL

AFTER DELIVERY

When you receive themachine, make sure that it has not been damaged during transportation and that no parts are missing. Only by giving us immediate advice can the necessary replacement parts be obtained. Ensure that all components are correctly adjusted.

GENUINE PARTS

K-Line spare parts and accessories have been specifically designed and developed for the machines produced. We would call your attention to the fact that non-genuine parts and accessories are not recommended by K-Line. The use of such replacement parts frees K-Line from all liability and makes the warranty void. The installation and/or use of non-genuine parts may, because of technical characteristics of construction, modify or influence the performance of the machine negatively.

IDENTIFYING THE MACHINE FOR REQUESTING SPARE PARTS

The machine is identified by the serial number on the metal plate on the machine. When requesting spare parts or maintenance service, please indicate the model and number of your equipment to ensure prompt and efficient attention.

TRACTOR REQUIREMENTS

10-14 Horsepower x width of machine in feet 25-35 Kilowatt x meter width of machine in meters Tractor weight must be same as or greater than the towed unit.

Hydraulic valves

1 x double spool (optional) 2800 PSI approximately

Hydraulic operating pressure

DEFINITIONS USED IN THIS MANUAL

DISC ARM IDENTIFICATION (REAR VIEW)

VIEW FROM REAR OF MACHINE

FRONT ARM

REAR ARM

BOLT TENSION

Top plate bolt tension 200ft lbs/271Nm

Disc bolt tension 250ft lbs/340Nm

Figure 2

Figure 3

Figure 4

2945D - 2965D 3PL SPEEDTILLER

OPERATOR & SAFETY MANUAL

R I S K M A N A G E M E N T

Risk management is the process of finding out what may cause an injury, deciding what may happen as a result, and doing something about it.

The steps of risk management are: • Identify the hazards to workplace health and safety arising from work activities • Assess the risks

• Determine and implement control measures to reduce risk • Monitor and review the effectiveness of the control measures IDENTIFYING HAZARDS

Prior to commencing work, all hazards related to the work tasks should be identified. The selection of the appropriate work procedure(s) will depend on the type of work procedure(s) and hazards involved. Regular safety inspections will also identify hazards and ensure that control measures are in place. RISK ASSESSMENT Risk assessment allows appropriate control measures to be developed. Once hazards have been identified, they should be assessed in terms of their potential to do harm. To assess risk, consideration should be given to probability and consequences. (SEE RISK ASSESSMENT SCORE CHART - Pg 8). RISK CONTROL Risk control is the process of eliminating or reducing risk factors. Control measures should be chosen and implemented to eliminate or reduce risk as far as practicable. When deciding on the most appro- priate measures to use, practicality and acceptance of the control measures should be considered. Safe Working Procedures will be developed for all high – medium risk hazards. MONITOR AND REVIEW CONTROL MEASURES The risk identification, assessment and control process requires regular monitoring to ensure the implemented control measures perform as originally intended and continue to prevent or adequately control the risk of injury or incident. Control measures should also be checked carefully to ensure that new hazards are not created, directly or indirectly, by the original control measures.

2945D - 2965D 3PL SPEEDTILLER

OPERATOR & SAFETY MANUAL

R I S K A S S E S S M E N T S C O R E C H A R T

Figure 5

AT ALL TIMES COMPLY WITH RECOMMENDATIONS AND REQUIREMENTS OF THE MANUFACTURER AND THE ENVIRONMENTAL PROTECTION AUTHORITY

2945D - 2965D 3PL SPEEDTILLER

OPERATOR & SAFETY MANUAL

CONT I NUED

R I S K A S S E S S M E N T

REVISED RISK SCORE

RISK SCORE

CODE

HAZARDS

CONTROL

ADJUSTING & CLEANING MUST ONLY BE DONE WHEN MACHINE IS LOWERED OR IN TRANSPORT POSITION AND ONLY AFTER ALL CHAINS AND BOLTS HAVE BEEN CHECKED FOR TIGHTNESS & WEAR IN THE LOWER POSITION. ENSURE JACK IS INSTALLED CORRECTLY & JACK RECEIVES REGULAR MAINTENANCE. KEEP FEET AND BODY CLEAR WHEN OPERATING. ENSURE NO PERSONNEL ARE BETWEEN TRACTOR & IMPLEMENT WHEN HITCHING/ UNHITCHING TRACTOR TO IMPLEMENT MACHINE MUST BE LOWERED INTO WORKING POSITION USING SUITABLE LIFTING EQUIPMENT BEFORE PRIMING IS EFFECTED. PRIME BY SLIGHTLY LOOSENING FITTING/S INTO CYLINDERS AND OPERATING TRACTOR HYDRAULICS TO ACHIEVE FULL UNINTERRUPTED TRAVEL OF CYLINDER SEVERAL TIMES TO BLEED AIR. THEN RE-TIGHTEN HYDRAULIC FITTINGS ENSURE JACK(S) ARE CORRECTLY POSITIONED AND TAKING WEIGHT BEFORE REMOVING DRAWBAR PIN. STICKERS WARN OPERATOR MAINTAIN REGULAR CHECKS ON HYDRAULIC SYSTEM FOR WEAR & CHECK ALL FITTINGS ARE SECURE ENSURE TRACTOR OIL FLOW IS LIMITED TO REDUCE FALLING SPEED OR DO NOT INTERRUPT MACHINE FALLING UNTIL MACHINE IS FULLY IN LOWERED POSITION SAFETY PINS MUST BE PUT IN PLACE AS SOON AS MACHINE IS PUT IN TRANSPORT POSITION AND IF TRAVELLING ON PUBLIC ROADS TO DISCONNECT HYDRAULICS FROM TRACTOR

CRUSHING - WHEN ADJUSTING AND CLEANING, AS MACHINE MAY DROP WITHOUT WARNING

1(A).

CRUSHING - IMPROPER USE OF JACK

1(B).

CRUSHING - WHEN HITCHING TRACTOR

1(C).

CRUSHING - PRIOR TO PRIMING HYDRAULIC SYSTEM, AS MACHINE MAY DROP WITHOUT WARNING

1(D).

SUDDEN LIFT OR DROP OF DRAWBAR, CAUSING SEVERE INJURY IF MACHINE BECOMES UNHITCHED PENETRATION OF OIL - BROKEN OR BADLY MAINTAINED HYDRAULIC LINES RUPTURE OF OIL LINES BY OVER PRESSURE WHEN MACHINE COMES TO SUDDEN STOP BEFORE FULLY LOWERED TO WORKING POSITION COLLISION - HYDRAULICS ACCIDENTALLY LOWERED WHEN MACHINE IS BEING OPERATED IN TRANSPORT

1(E).

2(A).

2(B).

Figure 6

ALL HAZARDS & RISKS ARE CONTROLLED THROUGH SAFE WORKING PROCEDURES & ADEQUATE SIGNAGE

2945D - 2965D 3PL SPEEDTILLER

OPERATOR & SAFETY MANUAL

It is the responsibility of the operators to: Read and understand your manual. Take time to familiarize yourself with the operation of this machine, particularly the safety signs and devices fitted to this machine.

USE OF MACHINE BEYOND ITS LIMITS OR INTENT OF OPERATION WILL VOID WARRANTY.

Slow down in terrain such as rocks, or other difficult operating conditions.

I MPORTANT NOT I C E

• Safe work procedure analysis must be performed before attempting to assemble this machine.

• Do not attempt to operate this equipment under the influence of Drugs & Alcohol. • K-Line Ag can not be held responsible for any injury, death or property damage in the process of assembling this machine.

For further information please contact :

AU: 1800 194 131

• Ensure hydraulic system is fully primed. Pg 19

2945D - 2965D 3PL SPEEDTILLER

OPERATOR & SAFETY MANUAL