Data Loading...
Pest Armor | Universal Installation Instructions
128 Downloads
1.58 MB
Twitter Facebook LinkedIn Copy link
RECOMMEND FLIP-BOOKS
2021 SHELVING INSTALLATION INSTRUCTIONS
R)and the rail clamps as pictured above. Align the components as shown above and then fasten togethe
Pest Armor | Architectural Steel Exclusion Mesh
2” 48” CASE PACK 40 PCS. - 160 LF 40 PCS. - 160 LF 21 PCS. - 160 LF 40 PCS.
Universal Industries
o I.B.S. Zanzibar, Forodhani NIGERIA GHANA UGANDA KENYA RWANDA ZANZIBAR TANZANIA SOUTH AFRICA UNIVER
Zoom Instructions
off using the options at the bottom left of the call screen. Note: You will only be able to see thes
EOI Instructions
EOI Instructions Evidence of insurability Instructions for online submission What is EOI and when is
Universal Industries 2020
o I.B.S. Zanzibar, Forodhani Physical Address Hertford O ce Park, Block D, 1st Floor, 90 Bekker Road
Installation and Annual Awards
neighborhood informat ion are subject to change wi thout not ice or obl igat ion. Home shown does no
Folding Activity Arch Instructions
Folding Activity Arch Instructions READ, FOLLOW AND KEEP THESE SAFETY IN
Swurl Spinner Instructions
Swurl Spinner Instructions SWURL SPINNER INSTRUCTIONS SS0312 READ, KEEP AND FOLLOW THESE SAFETY INST
INSTALLATION INSTRUCTIONS
INSTALLING PEST ARMOR ON OFFSET SURFACES
› Lay out sections of Pest Armor along the offset surface. › Install each section of Pest Armor by applying downward pressure to the bottom tab, while pushing up towards the second surface. Secure the bottom tab every 12”, using neoprene-washered screws (included), keeping the Pest Armor tight to both surfaces. › Overlap all seams 1”.
TURNING PEST ARMOR 90° ON OFFSET SURFACES
› At the point of your desired 90° turn, make 1 relief cut on the top tab of your Pest Armor. Bend the Pest Armor 90° to meet the offset surface. › Flatten and secure the top tab as needed. Secure the bottom tab every 12” using neoprene-washered screws (included). › If necessary, add relief cuts to the bottom and middle tab to allow Pest Armor to flex for compounding angles (such as a roof ridge vent end cap). Start in the middle of the end cap for the first relief cut and then add one relief cut on each side, approximately 1” from the center cut. Add more cuts as necessary.
PAINT ALL EDGES THAT HAVE BEEN CUT DURING INSTALLATION TO SEAL AND PROTECT PEST ARMOR FROM RUST OR CORROSION
1/4”
3/8”
WOVEN MESH
EXPANDED MESH
ARCHITECTURAL MESH EXCLUSION PROFILES
L-MESH
LOW PROFILE Z-MESH
HI PROFILE Z-MESH
PEST ARMOR ™ MESH
PROFILE
LENGTH CASE PACK
RAML350
1/4” Woven Mesh L-Mesh
48”
20 PCS / 80 LF
RALP1448B
1/4” Woven Mesh Low Profile Z-Mesh 48”
40 PCS / 160 LF
RALP1491B
1/4” Woven Mesh Low Profile Z-Mesh 91-1/2”
21 PCS / 160 LF
RA1448B
1/4” Woven Mesh Hi Profile Z-Mesh 48”
40 PCS / 160 LF
RA1491B
1/4” Woven Mesh Hi Profile Z-Mesh 91-1/2”
21 PCS / 160 LF
RA3848B
3/8” Expanded Mesh Hi Profile Z-Mesh 48”
40 PCS / 160 LF
PEST ARMOR EXCLUSION APPLICATIONS
SOLAR PANEL
RIDGE VENT
FOUNDATION SILL PLATE
DON’T JUST REMOVE. EXCLUDE. INDUSTRY PROVEN WILDLIFE EXCLUSION PRODUCTS. MADE IN THE USA SINCE 1947.
PAUIS_REV1
10950 Linpage Place St. Louis, MO 63132 | 800-325-7076 | www.hy-c.com | [email protected]